2552型

Cryo Cartridge标本持有人
  • 对于盒中包含的标本,需要液氮冷却以转移到冷冻电子显微镜(Cryo-EM)的透射电子显微镜(TEM)
  • 允许在标准TEM中进行标本预先筛选以确定标本质量,以自动装载系统最大限度地提高先进TEM中的吞吐量和数据收集
  • 基础温度小于-175°C
  • Preserves the specimen’s vitreous state during transfer
  • Advanced mechanism for frost-free transfer
  • 用于无工具样品安装的集成夹具
  • 分辨率优于0.20 nm
  • 低漂移率为1.5 nm / min-1

预定标本质量最大化Cryo-EM吞吐量

了解标本质量是Cryo-Em的一个关键方面。由于样品制备方法不一致,试样通常可以是晶体,这可以防止有意义的数据收集。

在高级TEM中,加载多个样本,然后单独地成像和分析,通常处于无人参与模式。当样本的质量小于理想时,有价值的时间浪费产生毫无意义的数据。

模型2552 Cryo Cryo Cartridge标本保持器是一种先进的单倾斜支架,可使用标准TEM来评估样品质量。然后可以将质量充分质量的标本加载到高级TEM中进行数据收集。

Cryo Cartridge标本保持器的关键特性是它在“反转转移”期间保持低温温度。也就是说,在TEM中成像后,样品在返回到Cryo工作站期间保持在Cryo温度下,以随后装入样品栅格盒。

Included with the Cryo Cartridge Specimen Holder is a cryo workstation, a temperature controller, a型号9010真空储存容器, and a specimen tool.

简单的样品装载和转移

标本尖端的创新设计使得包含墨盒的栅格的装载和卸载非常容易。要加载墨盒,保持器插入Cryo工作站以冷却。保持器杜瓦和Cryo工作站都填充有液氮。

The modular design of the cryo workstation allows the reservoirs to be repositioned to enhance ease-of-use for both right- and left-handed operation.

一旦温度小于-175°C的实现d, a cartridge is loaded from the grid box into the holder tip. The holder accepts a 3.5 mm diameter cartridge, which is secured by the holder’s one-piece, integrated clamp.

The clamp automatically closes when the holder tip is retracted. Optionally, the clamp can be closed with forceps or with the supplied tool. The thin profile of the clamp maximizes specimen visibility.

样品支架尖端缩回位于支架内的主动冷却的Cryo屏蔽内。该屏蔽可防止在转移到显微镜期间在样品上形成缩合。在从显微镜转移到工作站后,将样品的玻璃化状态保持在用自动装载系统在Cryo-EM中进行后续成像。

Rapid cool down, extended hold time

在Cryo工作站或TEM中,Cryo盒样品支架在低于-175°C的工作温度迅速达到-175°C。随着200毫升露天能力,容易获得超过4小时的持续时间。沸石吸收介质增强了杜瓦真空。温度控制器直接连接到样品架露天度,并显示保持器尖端温度。

再生沸石

必须定期再生露珠沸石。使用温度控制器上的单触沸石再生按钮轻松实现此过程。188bet体育国际Fischione推荐这一点Model 9030 Turbo Pumping Station在再生过程中疏散杜瓦。

血浆清洁

在冻结薄膜之前,应清洁TEM碳支撑栅格以去除碳氢化合物并使网格表面亲水。188bet体育国际Fischione建议您清洁支持网格1020型等离子体清洁剂orModel 1070 NanoClean

Collision protection

188bet体育国际Fischione.’s advanced specimen holders are compatible with the TEM’s touch alarm that stops goniometer movement if a pole touch occurs. Follow the microscope manufacturer’s recommendation for operating the goniometer at high-tilt angles.